[2023] Get Top-Rated HP HPE6-A75 Exam Dumps Now
Passing Key To Getting HPE6-A75 Certified Exam Engine PDF
NEW QUESTION # 17
Refer to the exhibit.
Which statements accurately describe the status of the Onboarded devices in the configuration tor the network settings shown? (Select two.)
- A. They will perform 802.1X authentication when connecting to the SSID.
- B. They will connect to secure_emp SSID after provisioning.
- C. They will use WPA2-PSK with AES when connecting to the SSID.
- D. They will connect to Employee_Secure SSID for provisioning their devices.
- E. They will connect to Employee_Secure SSID after provisioning.
Answer: A,B
NEW QUESTION # 18
Refer to the exhibits.
Refer to the exhibits. The network administrator enters the commands shown in Exhibit 2. What is the spanning tree status on Al and A2?
- A. A1 towards traffic, and A2 blocks traffic.
- B. A1 blocks traffic, and A2 forwards traffic.
- C. Both Al and A2 block traffic.
- D. Both A1 and A2 forward traffic
Answer: D
NEW QUESTION # 19
OSPF is configured on an AOS-Switch, and the network administrator sets the router ID to
10.0.0.1. The administrator wants to be able to reach the switch at this ID from any location throughout the OSPF system. The administrator also needs the router ID to De stable and available, even if some links on the switch fail.
What should the administrator do?
- A. Configure 10.0.0.1 as a secondary IP address on the switch 00BM poet.
- B. Configure 10.0.0.1 on a loopback interface, and enable OSPF on that interface.
- C. Configure 10.0.0.1 as a manual OSPF neighbor on each switch in the OSPF system.
- D. Make sure that 10.0.0.1 is the IP address on the VLAN with the lowest ID.
Answer: B
NEW QUESTION # 20
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. an issue with queuing, caused by mismatched QoS settings
- B. asymmetric routing introduced by a routing configuration error
- C. a hardware issue, such as a broken cable
- D. mismatched IP addresses on the VLAN for the link
Answer: C
NEW QUESTION # 21
Which situation requires an AOS-Switch interface to support MAC-based VLANs?
- A. The interface has an extended MAC ACL applied to it in the inbound direction, and it has multiple tagged VLAN assignments.
- B. The interface has an extended MAC ACL applied to it in the outbound direction, and it uses VLAN ID as one of the criteria for rules.
- C. The interface is configured to support 802.1X in user-based mode, connects to more than one endpoint at a time, and users are assigned to different dynamic VLANs.
- D. The interface is configured to support Local MAC Authentication (LMA), authenticates endpoints against a non-default MAC group, and limits the address count to 1.
Answer: A
NEW QUESTION # 22
Refer to the exhibit.
An employee connects a corporate laptop to the network and authenticates for the first time using EAP-TLS. Based on the Enforcement Policy configuration shown, which Enforcement Profile wilt be sent?
- A. Onboard Device Repository
- B. Deny Access Profile
- C. Onboard Pre-Provisioning - Aruba
- D. Onboard Post-Provisioning - Aruba
Answer: C
NEW QUESTION # 23
An administrator supports a RAP to a branch office. Employees at the branch office connect to an employee SSID that allows for split tunneling of the employee traffic. The RAP initially connects to the corporate office controller, but later loses connectivity to it.
Which operating mode should the administrator configure for a secondary SSID to be advertised during the loss of connectivity?
- A. Backup
- B. Standard
- C. Always
- D. Persistent
Answer: D
NEW QUESTION # 24
An administrator needs to authenticate users connected to an ArubaOS Switch where the switch authenticates the user, assigns the firewall policies to the user, and processes some of the users' traffic. Which connection method should the administrator configure on the ArubaOS-Switch?
- A. Split-tunneled mode
- B. Per-user tunneled node
- C. Per-port tunneled node
- D. VLAN tunneled mode
Answer: C
NEW QUESTION # 25
Refer to the exhibit.
Traffic between the servers m Area l takes a less optimal path rather than the link associated with VLAN l OOO, subnet 10.0.0.0/30. Based on the exhibits, why is this the case?
- A. Switch-1 and Switch-2 cannot achieve adjacency on VLAN 1000 due to mismatches.
- B. The link between Switch-1 and Switch-2 has gone down.
- C. OSPF routing switches choose the best intra-area routes based on Area 1 links only.
- D. The metric on the VLAN 1000 interface is too low.
Answer: C
NEW QUESTION # 26
OSPF is configured on an AOS-Switch, and the network administrator sets the router ID to 10.0.0.1. The administrator wants to be able to reach the switch at this ID from any location throughout the OSPF system. The administrator also needs the router ID to De stable and available, even if some links on the switch fail.
What should the administrator do?
- A. Configure 10.0.0.1 as a secondary IP address on the switch 00BM poet.
- B. Configure 10.0.0.1 on a loopback interface, and enable OSPF on that interface.
- C. Configure 10.0.0.1 as a manual OSPF neighbor on each switch in the OSPF system.
- D. Make sure that 10.0.0.1 is the IP address on the VLAN with the lowest ID.
Answer: B
NEW QUESTION # 27
Why is a terminate session enforcement profile used during posture checks with 802.1 x authentication?
- A. To send a RADIUS CoA message from the ClearPass server to the client
- B. To force the user to re-authenticate and run through the service flow again
- C. To remediate the client applications and firewall do that updates can be installed
- D. To blacklist the user when they are in an unhealthy posture state
- E. To disconnect the user for 30 seconds when they are in an unhealthy posture state
Answer: A
NEW QUESTION # 28
An administrator implements the MultiZone feature and uses two clusters that utilize CPSec. A primary and a data zone are created. MultiZone APs successfully build sessions to the primary cluster but fail to establish sessions to the data zone cluster.
What must the administrator do to solve this problem?
- A. Enable CPSec in the MultiZone profile for both the primary and data zone.
- B. Add the MultiZone APs to the data zone's CPSec whitelist.
- C. Use different AP Group names for the two zones.
- D. Enable MultiZone booting in the MultiZone AP apboot configuration mode.
Answer: C
NEW QUESTION # 29
An administrator mistakenly configures the wrong VLAN setting on a managed controller's interface. This causes the controller to lose management access to the Mobility Master (MM).
Which mechanism will then attempt to restore the previous working configuration on the managed controller?
- A. restore config
- B. disaster recovery
- C. bulk configuration
- D. auto-rollback
Answer: D
NEW QUESTION # 30
Refer to the exhibit.
Controllers are configured m a cluster as shown in the exhibit. These are the network details.
- A Mobility Master (MM) manages the cluster.
- The cluster contains two controllers: Cl and C2.
- API and AP2 use C1 as their Active AP Anchor Controller (A-AAC) with
C2 as their Standby AAC (S-AAC).
- AP3 and AP4 use C2 as their A-AAC, with C1 as their S-AAC.
User1 establishes a wireless connection via API, where the Active User Anchor Controller (A- UAC) assigned is C1, with C2 as the standby. What happens when User1 roams the wireless network and eventually their session is handled by AP3?
- A. The AP3's A-AAC switches to C1, and the user's A-UAC remains on C1.
- B. The AP3's A-AAC switches to C2, and the user's A-UAC remains on C1.
- C. The AP3's A-AAC switches to C2, and the user's A-UAC remains on C2.
- D. The AP3's A-AAC switches to C1, and the user's A-UAC remains on C2.
Answer: B
Explanation:
The user VLAN or AP group will not directly affect whether cluster is L2 or L3. Each MC will probe its VLANs and will only choose L3 if the VLAN config is mismatched or the MC itself is in a different VLAN itself. The cluster should be L2 thus the APs will retain A-AAC unless rebalance or failure. The user will do the same for the U-AAC.
NEW QUESTION # 31
Refer to the exhibit.
The network administrator needs to set up BGP between the two company switches. Switch-1 and Switch-2. The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?
- A. Enable the multihop option for the neighbor on each of the switches.
- B. Set the update source for the neighbor to the local loopback interface on each switch.
- C. Enable BGP on the interfaces that the switches use to reach each other.
- D. Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.
Answer: B
NEW QUESTION # 32
What is a primary use case for RPVST+ on AOS-Switches?
- A. seamless integration with RSTP
- B. enhanced loop protection in an MSTP network
- C. integration of AOS-Switches in a heterogeneous vendor network that uses the Cisco protocol
- D. more granular load balancing than MSTP when access switches connect to two core switches
Answer: C
NEW QUESTION # 33
An administrator implements the MultiZone feature and uses two clusters that utilize CPSec. A primary and a data zone are created. MultiZone APs successfully build sessions to the primary cluster but fail to establish sessions to the data zone cluster. What must the administrator do to solve this problem?
- A. Enable CPSec in the MultiZone profile for both the primary and data zone.
- B. Add the MultiZone APs to the data zone's CPSec whitelist.
- C. Use different AP Group names for the two zones.
- D. Enable MultiZone booting in the MultiZone AP apboot configuration mode.
Answer: C
NEW QUESTION # 34
Refer to the exhibit.
Based on the configuration of the Enforcement Profiles In the Onboard Authorization service shown, which Onboarding action will occur?
- A. The device will be disconnected from and reconnected to the network after Onboarding is completed.
- B. After logging in on the Onboard web login page, the device will be disconnected form and reconnected to the network before Onboard begins.
- C. The device will be disconnected after post-Onboarding EAP-TLS authentication, so a second EAP-TLS authentication is performed.
- D. The device will be disconnected from the network after Onboarding so that an EAP-TLS authentication is not performed.
- E. The device's onboard authorization request will be denied.
Answer: A
NEW QUESTION # 35
......
HPE6-A75 exam questions for practice in 2023 Updated 72 Questions: https://certkingdom.pass4surequiz.com/HPE6-A75-exam-quiz.html